Right Crete UW

 

  Right Crete UW
MSDSspacerPDF

 

DESCRIPTION
RIGHT CRETE UW is a quick setting, cement based patching material designed to set up under water. RIGHT CRETE UW will take initial set in 5 minutes and final set in 20 minutes. Following the initial set, it may be shaved or contoured to the desired finish.

USE AND APPLICATIONS

RIGHT CRETE UW should be used where contact with water or moisture is expected.
• Piers
• Tunnels
• Concrete Pipe
• Pilings
• Manholes

FEATURES AND BENEFITS
• High strength, over 5000 psi in 28 days
• Will stop active leaks
• Economical, 1/2 the cost of hydraulic cements
• May be shaved or formed

Coverage Rates
A 50 lb bag will yield approximately .50 cubic feet

SHELF LIFE
Minimum of 1 year stored in dry protected storage.

PACKAGING
• 50 lbs bag

APPEARANCE
Concrete gray

SHELF LIFE
Minimum of 1 year stored in dry protected storage.

DIRECTIONS FOR USE:
SURFACE PREP

Remove all dirt, grease, oil and other contaminants that may come in contact with the patching material. Surface must be damp to achieve proper bond.

MIXING
RIGHT CRETE UW will require approximately 5 quarts of water per 50 lb unit. Add the powder to the water and mix to a no slump consistency. Mix for no more than 60 seconds. Do not mix more that can be applied in 3 minutes.

APPLICATION
Always overfill the area to be patched. Once initial set has occurred, shave the patch to its desired finish. Always shave toward the bond lines. Finish with a steel trowel. Underwater patching is typically done by a hand packing and finishing method.

CLEAN UP
Clean tools with water immediately after use

 

 
 

MATERIAL PROPERTIES

ASTM C109
Compressive Strength, PSI
  24 Hour 3500
  7 Day 5400
  28 Day 6100
ASTM C266
Set Time, Gilmore
  Initial 3-5 Min
  Final 20 Min
ASTM C190
Tensile Strength, PSI
  7 Day Ave. 315
  28 Day Ave. 410
ASTM C78
Flexural Strength, PSI
  28 Day Ave. 965
ASTM C666
Freeze Thaw Durability Factor
  300 Cycles 98%
ASTM C157
Shrinkage 50% RH
  28 Day Ave. -0.160%
Expansion 100% RH
  28 Day Ave. 0.104%
ASTM C672
Scaling Resistance
  25 Cycles 0% Loss
ASTM D1411
  Chlorides <0.01%

RESTRICTIONS
Do not re-temper
Do not over water
Do mix to a putty like consistency
Do add powder to the water
Do wear gloves when hand packing

TECHNICAL SERVICE
For conditions not specified, application procedures not noted,
contact: Right Pointe Company (888) 755-5700

LIMITED WARRANTY
Every reasonable effort is made to apply RIGHT POINTE COMPANY exacting standards both in the manufacture of our products and in the information which we issue concerning these products and their use. We warrant our products to be of good quality and will replace or, at our election, refund the purchase price of any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement or refund, RIGHT POINTE COMPANY MAKE NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and RIGHT POINTE COMPANY shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the RIGHT POINTE COMPANY Technical Manager.

 

 
   

ABOUT US

 

OUR PRODUCTS
Expansion Joints and Plastics
Joint Sealants
Chemical Liquids
Cement Powders and Liquids
Waterproofing
Epoxies

 

CONTACT US

 

FEATURED PRODUCTS

 
© 2011-2014 All Rights Reserved Right Pointe Company