DESCRIPTION
CLEAR WATER LINSEED OIL Curing Compound is a membrane forming
treatment utilizing a boiled linseed oil base combined in a treated
clear water solution. This product meets the maximum VOC
content limit (700 g/L) for concrete curing and sealing compounds as required by the U.S. EPA Architectural Coatings Rule.
For use on just-finished exterior concrete surfaces, CLEAR WATER LINSEED OIL is a one pass penetrating sealer to maximize water
retention during the concrete hydration phase.
• This product meets the maximum VOC content limit (700 g/L) for concrete curing and sealing compounds as required by the U.S. EPA Architectural Coatings Rule
• Protects against salt and other de-icing chemicals
• Sprays on milky white – dries clear
• Preferred by many flooring system suppliers
• Supplied in ready-to-use formula; no mixing

SPECIFICATIONS
• ASTM C-309, Type I, Class A
• AASHTO M-148, Type I, Class A
• State D.O.T.’s
• Fed Spec. TT-L-190

USE AND APPLICATIONS
CLEAR WATER LINSEED OIL should be applied to just-finished concrete (once surface water is gone and it can be walked on without damage). For existing concrete, clean thoroughly of all contaminants prior to application.
Roller, low-pressure sprayer or brush are all acceptable methods of application. Do not pond or puddle. Fast drying–restrict foot traffic until tack free (2-3 hours minimum).
Clean tools immediately with warm soapy water. Once film has dried, use of appropriate solvents may be necessary. Proper disposal of linseed oil soaked materials is required.
• Industrial/commercial flooring
• Driveways
• Plaza decks
• Sidewalks

FEATURES AND BENEFITS
• Maximum protection available against salt and de-icing chemicals.
• Slows surface degradation process
• Extended service life

Coverage Rates

PACKAGING
• 5 gallon pails
• 55 gallon drums
• 275 gallon Tote

Drying Time
May be extended dependent on weather conditions and coverage rate. Restrict pedestrian foot traffic until surface is completely dry.

APPLICATION PROCEDURES
• Incompatible with solvent containing products
• Ready to use formulation – no dilution required
• Aggressive mixing is not required and will result in excess foaming
and stripping
• Spray evenly in a one coat application after the surface is free of all
bleed water
• Use a spray rate of approximately ½ gallon per minute not exceeding 45 psi of pressure with any conventional piece of spray equipment.
• Clean up is accomplished with warm soapy water.

RESTRICTIONS
Not to be applied at temperatures below 40°F.
Protect from freezing.
Best results are achieved when used within 1 year.
Not compatible with solvents.
Prior to subsequent floor treatment, additional cleaning may be necessary to remove any remaining film.
May darken concrete surfaces that have been densely troweled.
Use at any air temperature so long as the concrete temperature exceeds 40°F for 24 hours.
The Material Safety Data Sheet refers to additional health and safety information

TECHNICAL SERVICE
For conditions not specified, application procedures not noted,
contact: Right Pointe Company (888) 755-5700

LIMITED WARRANTY
Every reasonable effort is made to apply RIGHT POINTE COMPANY
exacting standards both in the manufacture of our products and in the information which we issue concerning these products and their use. We warrant our products to be of good quality and will replace or, at our election, refund the purchase price of any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement or refund, RIGHT POINTE COMPANY MAKE NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and RIGHT POINTE COMPANY shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the RIGHT POINTE COMPANY Technical Manager.